Plumber's Essentials: Your Key to Installing a Bathtub
Plumber's Essentials: Your Key to Installing a Bathtub
Blog Article
We have unearthed this article on Tools You Need to Install a New Bathtub listed below on the web and concluded it made good sense to write about it with you on this page.
Setting up a bath tub isn't exactly brain surgery, yet it does need strong plumbing, woodworking, as well as sometimes, tiling skills. Replacing an old bath tub with a brand-new one is likewise a moderately tough task. If the old bathtub is easily available, the project can relocate rapidly; if you have to open up a wall surface to eliminate the old bathtub as well as place the new bathtub, the job is much harder. In either case, the project is within a house handyman's abilities, although you will require a helper to leave the old bathtub and set in the new one. Ensure you have certified yourself for the task and also fit trying it. As opposed to employing a professional to take over a halfway-completed job, it is much better to consider employing one before you begin. Chances are you may need a professional plumber to make tube links.
This write-up will certainly assist you set up a brand-new tub in your shower room if you have currently gotten a new bathtub and also do not need to transform the plan of your previous supply of water pipelines.
Your tools and also material list must consist of the following:
Preparing for the Installment
Firstly, the supporting structure provided with the bathroom needs to be fitted (if required) according to the manufacturer's instructions. Next, fit the faucets or mixer to the bath tub. When suitable the tap block, it is necessary to see to it that if the faucet includes a plastic washing machine, it is fitted between the bath and also the taps. On a plastic bathroom, it is likewise reasonable to fit a sustaining plate under the faucets unit to avoid stress on the tub.
Fit the flexible faucet adapters to the bottom of the two taps making use of 2 nuts as well as olives (in some cases provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and then pass the electrical outlet with the hole in the bath. Utilize the nut supplied by the maker to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the flexible overflow pipeline to the overflow outlet. Afterwards, screw the pipe to the overflow face which should be fitted inside the bath. See to it you make use of all of the provided washing machines.
Attach the trap to the bottom of the waste electrical outlet on the tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and screw on the catch to the electrical outlet. Attach all-time low of the overflow tube in a comparable manner.The bathroom need to currently be ready to be fitted in its final placement.
Removing Old Touches
If you need to change old faucets with new ones as a part of your setup, then the first thing you need to do is separate the water system. After doing so, switch on the faucets to drain pipes any type of water staying in the system. The procedure of eliminating the existing taps can be fairly troublesome due to the limited gain access to that is typically the instance.
Use a container wrench (crowsfoot spanner) or a faucet tool to reverse the nut that links the supply pipes to the taps. Have a towel ready for the staying water that will originate from the pipelines. When the supply pipes have been eliminated, use the very same device to loosen the nut that holds the faucets onto the bath/basin. You will require to quit the single taps from transforming during this process. Once the taps have actually been gotten rid of, the holes in the bath/basin will have to be cleaned up of any type of old sealing compound.
Prior to moving on to fit the brand-new faucets, contrast the pipe links on the old taps to the new taps. If the old taps are longer than the brand-new taps, after that a shank adapter is needed for the new taps to fit.
Mounting the Tub
Using both wood boards under its feet, put the tub in the needed setting. The wood boards are valuable in equally spreading the weight of the tub over the area of the boards instead of concentrating all the weight onto four little points.
The following objective is to make sure that the bathtub is leveled all round. This can be attained by checking the spirit level and also readjusting the feet on the bath tub until the spirit level checks out level.
To set up taps, fit the bottom of the furthest versatile tap adapter to the appropriate supply pipeline by making a compression sign up with; after that do the very same for the various other tap.
Switch on the water supply and examine all joints as well as new pipework for leaks and also tighten them if needed. Fill up the bathtub as well as likewise check the overflow outlet as well as the normal electrical outlet for leakages.
Finally, deal with the bathroom paneling as defined in the producer's user's manual. Tiling and also securing around the bath tub should wait till the bathtub has actually been utilized at the very least once as this will resolve it into its final setting.
Suitable New Touches
If the tails of the new faucets are plastic, after that you will need a plastic connector to avoid damages to the thread. One end of the port fits on the plastic tail of the tap as well as the other end gives a connection to the existent supply pipelines.
If you require to fit a monobloc, after that you will need lowering couplers, which links the 10mm pipeline of the monobloc to the basic 15mm supply pipeline.
Next off, place the faucet in the placing opening in the bath/basin making certain that the washing machines are in place in between the tap and also the sink. Protect the tap in position with the producer given backnut. Once the tap is safely in position, the supply pipes can be attached to the tails of the taps. The faucets can either be connected by utilizing corrugated copper piping or with regular faucet connectors. The former kind should be linked to the faucet finishes initially, tightening up only by hand. The supply pipes can later on be attached to the other end. Tighten both ends with a spanner after both ends have been linked.
Tiling Around the Bath tub
In the location where the bathroom fulfills the tile, it is required to seal the joins with a silicone rubber caulking. This is necessary as the installation can relocate sufficient to split a stiff seal, triggering the water to permeate the wall in between the bathroom as well as the tiling, resulting in problems with dampness and also feasible leaks to the ceiling listed below.
You can select from a variety of coloured sealers to assimilate your fixtures and fittings. They are offered in tubes and also cartridges, and are capable of sealing voids up to a width of 3mm (1/8 inch). If you have a larger gap to load, you can fill it with spins of soaked paper or soft rope. Remember to always fill the tub with water before sealing, to enable the motion experienced when the tub remains in usage. The sealant can fracture rather very early if you do not take into consideration this movement prior to sealing.
Conversely, ceramic coving or quadrant ceramic tiles can be made use of to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and reduce to dimension, are also quickly available on the market. It is suggested to fit the tiles utilizing waterproof or waterproof adhesive as well as cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I'm certainly very enthusiastic about How to Install a Bathtub and I'm hoping you enjoyed reading the entire article. I beg you set aside a second to distribute this blog posting if you enjoyed it. We thank you for reading our article about A Step-by-Step Guide to Installing a Bathtub.
Urgent plumbing? Call. Report this page